Misting Nozzle Kit 50-Pack 4-Outlet Atomizing Sprinkler Nozzles Lake Blue 6x6 cm Plastic Irrigation Accessory for Garden Greenhouse Lawn

This fifty-piece atomizing nozzle kit brings distributed fine mist capability to small-scale irrigation and humidification projects. Use the set to add gentle surface dampening across benches, edges, planter arrays, and covered outdoor runs while minimizing pooling and runoff. Install units along flexible micro tubing and tune spacing to match canopy density and desired humidity levels.Specifications:Material: Molded non- odorless plasticColor: Lake BlueWeight: Approx. 24.1 oz (683 g)Product Size: Approx. 6 x 6 cm (2.4 x 2.4 in)Hook Inner Diameter: Approx. 4 mm (0.16 in)Pack Quantity: 50 nozzles + 50 small hooksIntended Pressure Range: Low-pressure microirrigation (use pressure regulator if connecting to higher-pressure source)Package Included:50 x 4-outlet atomizing nozzles50 x small hooksQ: What does the kit include and how many pieces are provided?A: The kit includes fifty 4-outlet atomizing nozzles and fifty matching small hooks, total kit weight about 24.1 oz (683 g).Q: What tubing and hook size is required for installation?A: The small-hook interface fits common micro tubing with an inner opening near 4 mm; push-fit installation typically requires no special tools.Q: Can the nozzles be used with untreated well water?A: Use inline strain screens or filters when source water contains sediment; untreated water with high particulate load may clog emitters and is not recommended without filtration.Q: How should I maintain the nozzles for seasonal use?A: Perform seasonal flushing and visual inspection, remove mineral deposits as needed, and replace any warped or worn components to preserve even distribution.Q: Are these nozzles rated for continuous immersion or high-pressure cleaning?A: No; components are intended for low-pressure microirrigation and routine outdoor exposure under shaded or supported installations, not for

• 【Material and Kit Specifications】: The set contains fifty 4-outlet atomizing nozzles and fifty matching small hooks with a combined weight of approximately 24.1 oz (683 g). Each nozzle measures about 6 x 6 cm and each hook inner diameter is near 4 mm. Components are molded from non-, odorless plastic to reduce uncertainty during selection, support repeatable seasonal installations, and simplify inventory management; intended for low-pressure microirrigation assemblies and routine outdoor use,
• 【Spray Distribution and Water Efficiency】: Four-outlet atomizing geometry provides an evenly distributed fine mist across a short radius to minimize pooling and reduce water per cycle compared with single-point emitters. This distributed pattern helps maintain plant surface humidity for conditioning and localized evaporative while enabling lower flow settings; not intended for use with unfiltered water containing heavy sediment or particulate matter without inline filtration to prevent
• 【Installation and Compatibility】: Push-fit small-hook interface accepts common micro tubing with a nominal inner opening near 4 mm and requires no special tools for insertion or removal. Typical spacing is adjustable by canopy density; begin at approximately 6 to 12 inches (15 to 30 cm) intervals and tune for desired coverage. Use inline strain screens to protect against debris; avoid sharp kinks in supply lines and add a pressure regulator when connecting to higher-pressure sources to maintain
• 【Durability and Maintenance Guidelines】: Molded bodies resist routine outdoor exposure when mounted under shaded eaves or support rails; perform seasonal flushing to remove mineral buildup from local water and replace worn nozzles to maintain uniform distribution. Lightweight emitter design reduces load on suspension points and speeds replacement of individual items. Not rated for continuous submersion or for cleaning methods that exceed typical microirrigation pressures.
• 【Typical Use Cases and Operational Limits】: Fifty-piece kit supports landscape edging lines, greenhouse bench arrays, rooftop planter runs, shade structure humidification, nursery benches and decorative bed applications in low-pressure microirrigation systems. Use within normal irrigation temperature ranges and avoid exposure to aggressive chemicals or sustained high-pressure cycles; always follow local plumbing and outdoor water-connection codes when integrating with mains supply.